a.裁切：將防火板裁切成所需要的尺寸，再?zèng)]邊多留1/4英寸(6mm）作為修邊之用，注意鋸齒是從色板的一面進去，這樣才可以避免切斷面產生缺口，若使用刀片切割防火板時，一定要注意同樣也是從色紙的一進刀，然后像切玻璃一樣的劃下去，才會有干凈，光滑，沒有缺口的切斷面。

a. Cutting: Cut the fireproof board into the required size, leaving an extra 1/4 inch (6mm) on the edge for trimming purposes. Note that the serrations enter from one side of the color board to avoid creating gaps in the cut surface. When using a blade to cut the fireproof board, be sure to also enter from the first side of the color paper and cut it like cutting glass to achieve a clean, smooth, and gapless cut surface.

b.涂膠：在防火板背面及基材表面均勻涂上強力膠，如果基材表面非常不平整或吸水性極強，手工需上兩次膠以使表面完全布膠。施工時注意由于季節、氣候、地區等原因。各品牌強力膠的揮發時間都會有所不同，根據強力膠的使用建議，結合實際操作及施工備件來決定揮發時間，如：使用脫水脲醛膠和白乳膠時，需要在室溫25-30度的條件下加壓十二個小時以上。

b. Glue application: Apply strong glue evenly on the back of the fireproof board and the surface of the substrate. If the surface of the substrate is very uneven or has strong water absorption, it is necessary to manually apply glue twice to fully coat the surface. Pay attention to seasonal, climatic, and regional factors during construction. The volatilization time of various brands of strong adhesive will vary. Based on the recommended use of strong adhesive, combined with actual operation and construction spare parts, the volatilization time will be determined. For example, when using dehydrated urea formaldehyde adhesive and white emulsion adhesive, it is necessary to pressurize at room temperature of 25-30 degrees for more than twelve hours.

c.貼板：等干到不粘手市，將防火板小心地放到基板上面，如果粘貼的面積非常大，最好能用木條先間隔著放在基板上面，再將防火板放到基板上，等對正后再將木條抽出，將防火板一步步地按壓到基板上。然后用流滾輪或抹布用力壓勻，同時避免殘余的空氣在里面。

c. Board pasting: When it is dry and not sticky, carefully place the fireproof board on the substrate. If the pasting area is very large, it is best to use a wooden strip to place it on the substrate first, then place the fireproof board on the substrate. After aligning, pull out the wooden strip and press the fireproof board step by step onto the substrate. Then use a flow roller or cloth to press evenly, while avoiding residual air inside.

d.修正：等以上的加壓工作做好了，就用修邊機或10度角之刃將多余的邊切去，最后再用較利的銼刀將接縫銼得圓滑些。千萬注意：只能向下銼，絕不可來回銼，以免切斷面不平整光滑！多余而滲出來的膠應該用小塊抹布以及溶劑清理干凈。這樣整個施工過程就完成了。

d. Correction: Once the above pressurization work is completed, use a trimming machine or a 10 degree blade to cut off the excess edges, and finally use a sharp file to smooth out the seams. Be careful: file downwards only, never back and forth to avoid uneven and smooth cutting surfaces! Excess glue that seeps out should be cleaned with a small cloth and solvent. This completes the entire construction process.

e.施工環境要求：一般建議在現場施工將防火板和基板放在同一環境中48小時，濕度在45%，不宜高于80%，溫度不低于18攝氏度。

e. Construction environment requirements: It is generally recommended to place the fireproof board and substrate in the same environment for 48 hours during on-site construction, with a humidity of 45%, not higher than 80%, and a temperature not lower than 18 degrees Celsius.

以上的精彩內容來自：富美家防火板更多精彩內容請點擊我們的網站查看更多：http://m.xamgdj.com

The above exciting content comes from: Fumijia fireproof board. For more exciting content, please click on our website to view more: http://m.xamgdj.com