There are various types of building materials, which can be divided into four categories based on their combustion performance, namely: non combustible materials (Class A), non combustible materials (Class B, Class B), combustible materials (Class C), and combustible materials (Class D). The fireproof board countertop material should be basically non combustible material. Non combustible materials (also known as A-grade materials) can only be classified as non combustible materials if they meet the following conditions when conducting non combustible tests according to GB/T5464-85

(1)由于材料嫩燒引起爐內平均溫升不超過50攝氏度

(1) Due to the tender burning of materials, the average temperature rise in the furnace does not exceed 50 degrees Celsius

(2)試樣平均持續嫌燒時間不超過

(2) The average continuous burning time of the sample shall not exceed

(3)試樣平均質量損失率不超過

(3) The average mass loss rate of the sample shall not exceed

一些無機板材(如氧鎂水泥板).雖然本身不會燃燒，但在火災的高沮作用下.極易分解、炸裂失去結構強度，有的還會釋放出大有毒氣體。因此，這些板材仍不能用作防火板臺面材。這就是我們防火板臺面材的作為防火使用的基本要求所在。

Some inorganic boards (such as magnesium oxide cement boards), although they do not burn themselves, are prone to decomposition, cracking, and loss of structural strength under the high pressure of fire. Some may also release large and most toxic gases. Therefore, these boards cannot still be used as fire-resistant tabletop materials. This is the basic requirement for our fireproof board countertop material to be used as a fireproof material.

刷畫銅防火板

Brush painted copper fireproof board

防火板臺面的施工要點謹記心中：典雅胡桃木防火板

Key points to remember in the construction of fireproof board countertops: elegant walnut fireproof board

(1)薄型防火涂料可按裝飾要求和涂料性質選擇噴涂、刷涂或輥涂等施工方式。

(1) Thin fire-resistant coatings can be applied by spraying, brushing, or roller coating according to decoration requirements and coating properties.

(2)薄型防火涂料每次噴涂厚度不應超過丹麥楓木防火板2.5mm,超薄型涂料每次涂層不應超過0.5mm.須在前一遍干操后方可進行后一遍施工。

(2) The thickness of each spray of thin fire-resistant coating should not exceed 2.5mm for Danish maple fire-resistant board, and the thickness of each coat of ultra-thin coating should not exceed 0.5mm. The construction of the next coat must be carried out after the previous dry operation.

(3)厚型防火涂料可選用噴涂或手工涂抹施工。

(3) Thick fireproof coatings can be applied by spraying or manual application.

卡布奇諾防火板 (4)厚型防火涂料宜用低速攪拌機攪羽織銅防火板拌，攪拌時間不宜過長，攪拌均勻即可，以免涂料中輕質骨料被過度粉碎影響涂層質量。

Cappuccino fireproof board (4) thick fireproof coating should be mixed with a low-speed mixer and woven copper fireproof board. The mixing time should not be too long, and it should be evenly mixed to avoid excessive crushing of lightweight aggregates in the coating and affecting the quality of the coating.

(5)厚型防火涂料每遏涂抹厚度圈線銅防火板宜為5 四季榆木防火板- 10mm，必須在前一道涂層基本干操或固化后方可進行后一道施工。

(5) The thickness of the thick fireproof coating should be 10mm for each round of copper fireproof board applied, and the next layer of construction can only be carried out after the previous layer of coating is basically dry or cured.

(6)水泥系厚型防火涂料在天氣極度干燥和陽光直射環境下應采取必要養護措施。風化灰木層防火板

(6) Necessary curing measures should be taken for cement based thick fireproof coatings in extremely dry weather and direct sunlight environments. Weathered gray wood layer fireproof board

(7)防火涂料攪拌好后應及時用完，超過其規定使用期不得使用。

(7) After mixing, the fireproof coating should be used up in a timely manner, and should not be used beyond its specified usage period.

(8)防火涂層的厚度應符合設計要求，施工時應隨時檢測涂層厚度。

(8) The thickness of the fireproof coating should meet the design requirements, and the coating thickness should be checked at any time during construction.

本文由富美家防火板友情奉獻.更多有關的知識請點擊: http://m.xamgdj.com真誠的態度.為您提供為全面的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待

This article is dedicated to the friendship of aluminum Fumeijia fireproof board. For more relevant knowledge, please click on: http://m.xamgdj.com Sincere attitude. We will provide you with comprehensive services. We will gradually contribute more relevant knowledge to everyone. Stay tuned